Superior Guardian 6x20 3-Deck, 36" Twin Screw Wash Plant, Unit #803
SN: #1036936
Carrier chassis Main frame constructed of wide flange structural steel beams Tridem axle with (12) 11x22.5 radial tires complete air brake system mudflaps on rear axle Travel lights with brake and directional signals Fifth wheel hitch (4) fixed, structural steel cribbing legs Common Grease points - 1-2 locations to grease entire plant Superior Guardian 6203 Horizontal Vibrating Screen Supply and Installation for a 6x20 3 deck, all pertinent items and components including: adjustable motor base, motor sheave, screen sheave, v-belts, drive guard Screen and all pertinent items and components are supplied by Superior Price includes the following items: 40 HP TEFC, 1800 RPM, 460 volt, 3 phase, 60 hz, screen drive motor screen subframe Screen is installed to operate in the horizontal position Right hand drive Superior 36" x 25' Twin Fine Material Washer Supply and Installation for a T36x28' FMW, all pertinent items and components 1/4" ASTM A36 Steel Outboard pillow block bearings Over-flow flume with adjustable weir Material discharge chute Tail end feed hopper and tub baffle Variable Speed 200tph Urethand wear shoes Spiral type shaft, haldf pithc flighted for high capacity with adjustable mounts Price includes the following items: (2) 15 HP TEFC, 1800 RPM, 460 volt, 3 phase, 60 hz, motor(s) V-belt drive with guard Dodge shaft mount gear box Screen discharge chutes Roll away chute Constructed of 1/4" Mild Steel with 1/4" AR liners Top deck chute discharges over the kingpin end of the chassis or onto middle deck cross conveyor, 25% Blending gates Middle deck chute discharges onto middle or bottom deck cross conveyor, 25% Blending gates Bottom deck chutes discharges onto bottom or "blends up" to middle deck cross conveyor, 25% blending gates AR liners on both sides of blending gates Fines hopper 3/8" AR Construction with conveyor belt lining adjustable rubber flashing full length Spray Bars (16) 1.5" Galvanized spray bars and elbows, brass nozzles Flexible rubber hosing from manifold to spray bars Manually adjsutable spray bar for each spray bar, mounted below walkway Water Manifold 8" bolt flange at ground level for fresh water hookup Fresh water feeds in from end Distributes water to: spray bars, slurry hopper, FMW wash back, and fines hopper Wire strainer to prevent large debris from entering Weir / Overflow Water "T"- pipe installed at weir discharge and plumbed to discharge to either side of plant Slurry Hopper Hydraulically folds from transport to operating position Accepts feed from conveyor, lined for wear protection Spray bars mounted inside hopper (2) 30" wide x 11' long reversing cross conveyors Structural steel channel main frame Mounted on rollers to manually move to discharge from either side of chassis Receive oversize material from respective middle and bottom decks Class II head end drive 7.5 HP motor, v-belt drive with drive guard Dodge shaft mount reducer Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging Tail pulley - 10" diameter wing pulley Shafts - turned and polished Dodgebearings Manual screw take-ups Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC Belting - 2 ply, 3/16" x 1/16" 220 PIW Belt splice - steel mechanical fasteners Primary belt scraper - Exterra® Belt Cleaner Walkway 3/16" diamond tread plate along both sides and feed end of screen Includes toe board, and two-rail handrail, bolt on Walkway access on both sides of the chassis with steep angle stair access Drain holes Hydraulic "lift-only" leveling jacks (4) 5" x 18" hydraulic cylinders (4) manual lever valves; (1) for each cylinder 13HP Honda Motor gasoline over hydraulic, enclosed cabinet Overhead Safety tie off Safety tie off over plant for workers to tie off when working on screen Folds down for transport Electrical control panel NEMA 4 enclosure and NEMA SQUARE D electrical components Wired to on-plant motors (1) 40 HP screen drive motor (2) 15 HP FMW drive motor with VFD (WEG variable frequency drive) (2) 7.5 HP reversing cross conveyors Amp guage on outside of panel Hour meter inside panel Warning horn and light Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel Mounted on skid frame with lifting eyes (mounted on ditch side of plant) Power cables from motors to place panel 30' from plant, cable storage tray inside frame above axles Includes 2 extra #2 starters Painted to match plant Electrical Required power is 480 v/ 3 ph / 60 hz Control panel and wiring are not included Guarding Price includes standard guarding Customer is responsible to have guarding inspected Paint (1) coat primer; (1) finish coat enamel in Superior Grey Owner's manual (1) copy included for operation and maintenance